$ 188.60
Phoenix Contact develops terminal blocks, power supplies, relays, connectors, signal conditioners, controllers & PLCs, I/O systems, Industrial Ethernet, controller system cabling, PCB terminal blocks & connectors, and surge suppression.
Item number | 2903693 |
Packing unit | 10 pc |
Minimum order quantity | 10 pc |
Product key | DK6953 |
Catalog page | Page 308 (C-5-2019) |
GTIN | 4046356759069 |
Weight per piece (including packing) | 90.29 g |
Weight per piece (excluding packing) | 90.29 g |
Customs tariff number | 85364190 |
Country of origin | PL |
Notes on operation | The outputs are not suitable for switching different outer conductors. |
Notes on operation | Do not use to separate SELV / PELV circuits from other circuits, because safe isolation is not guaranteed. |
Product type | Single relay |
Operating mode | 100% operating factor |
Mechanical service life | approx. 2x 107 cycles |
Insulation characteristics | |
Insulation | Basic insulation |
Overvoltage category | III |
Pollution degree | 3 |
Data management status | |
Date of last data management | 17.01.2025 |
Maximum power dissipation for nominal condition | 1.44 W |
Test voltage (Winding/contact) | 2.5 kVrms (50 Hz, 1 min., winding/contact) |
Test voltage (Changeover contact/changeover contact) | 2.5 kVrms (50 Hz, 1 min., changeover contact/changeover contact) |
Rated insulation voltage | 250 V AC |
Rated surge voltage | 4 kV |
Coil side | |
Nominal input voltage UN | 24 V DC |
Input voltage range | 20.4 V DC … 26.4 V DC (20 °C) |
Drive and function | monostable |
Drive (polarity) | polarized |
Typical input current at UN | 60 mA |
Input power dissipation for UN | 1.44 W |
Typical response time | 18 ms |
Typical release time | 20 ms |
Protective circuit | Freewheeling diode |
Status display | LED (yellow) |
Coil resistance | 430 Ω ±10 % |
Switching | |
Contact switching type | 3 changeover contacts |
Type of switch contact | Single contact |
Contact material | AgNi |
Maximum switching voltage | 250 V DC |
440 V AC | |
Minimum switching voltage | 10 V (At 24 mA) |
Limiting continuous current | 10 A |
Maximum inrush current | 30 A (20 ms, N/O contacts) |
Min. switching current | 10 mA (at 24 V) |
Interrupting rating (ohmic load) max. | 240 W (at 24 V DC) |
124 W (at 48 V DC) | |
108 W (at 60 V DC) | |
52 W (at 110 V DC) | |
48 W (at 220 V DC) | |
2500 VA (for 250 V AC) | |
Motor load according to UL 508 | 1/2 HP, 240 V AC (N/O contact) |
Connection method | Plug-in connection |
Width | 35 mm |
Height | 35 mm |
Depth | 54.4 mm |
Ambient conditions | |
Degree of protection | RT I |
Degree of protection (Installation location) | ≥ IP54 (Installation location) |
Ambient temperature (operation) | -40 °C … 70 °C |
Ambient temperature (storage/transport) | -40 °C … 85 °C |
Altitude | ≤ 2000 m |
Standards/regulations | IEC 60664 |
IEC 61810 |
Corrosive gas test | |
Identification | ISA-S71.04. G3 Harsh Group |
EN 60068-2-60 |
Mounting position | any |
Weight | N/A |
---|---|
MOQ(pcs) |
INOSAKI Limited
RM B 5/F Gaylord Comm,
Bldg 114-118 Lockhart Rd.
Hong Kong
INOSAKI Sdn. Bhd.
2-1-9, Ground Floor, One Square, Tingkat Mahsuri 1,
11900 Bayan Lepas, Penang
INOSAKI Pte. Ltd.
101 Upper Cross Street,
No. 06-17, People’s Park Centre,
Singapore (058357)